Securty is a matter of great concern to all of us in this world. Normally there are four types of security threat to our property. 1 )Thief, an inturder. 2)Fire, so we use fire sensor. 3)Water spilage /over flow, so we use water sensor. 4) Gas leak , we use gas sensor, whenever there is security breach from one of above or any combination of above.
The project takes the following action
1) Sounds an ALARM to attract your or public attention .
2) If the reset sw is not pressed within 30 seconds the projects takes further action,
3) It makes an emergency call to deliver an emergency message stored in speech IC.
4) It will make five attempts to call you before it checks the conditions again.
The project presented here is based on world’s most powerful intel’s mcs-51 family of microcontroller atmel at89c51.
1) Sounds an ALARM to attract your or public attention .
2) If the reset sw is not pressed within 30 seconds the projects takes further action,
3) It makes an emergency call to deliver an emergency message stored in speech IC.
4) It will make five attempts to call you before it checks the conditions again.
The project presented here is based on world’s most powerful intel’s mcs-51 family of microcontroller atmel at89c51.
CIRCUIT EXPLANATION:
This project is based on 8051 microcontroller.(IC2)
IC3 is 74245 and is used as buffer.
IC4 P89021 is a one time programmable(otp) chip where messages are stored. This is 21 second speech ic where total of 12 messages can be recorded on eight different locations, but total duration should not be more than 21 seconds. Recorded messages can be played back by setting the trigger pin 10 & 11 to high, making these pin low will stop the message, Setting these pin high will repeatedly replay the same message.
This project is based on 8051 microcontroller.(IC2)
IC3 is 74245 and is used as buffer.
IC4 P89021 is a one time programmable(otp) chip where messages are stored. This is 21 second speech ic where total of 12 messages can be recorded on eight different locations, but total duration should not be more than 21 seconds. Recorded messages can be played back by setting the trigger pin 10 & 11 to high, making these pin low will stop the message, Setting these pin high will repeatedly replay the same message.
Ic LM 386(IC5) is an audio amplifire . Audio output from speech ic(IC4) pin no 7 cout is coupled to this ic on pin no 3 through VR2 volume control and C10. Amplified output from pin no 5 drives the speaker through capacitor C14. R14 and C13 corrects the tone. .C15 and C16 couples the audio message to telephone line.
C11 connected to pin no 6 of IC5 through R26 current limiting resistor is filter and C12 is noise suppressor.
IC4 needs 3.3v operating voltage .R9 is a voltage dropping resistor, D7 is 3.3v zener diode and C7 is a filter capacitor. These components will always maintain the voltage to3.3v at pin 9,12 of IC4. capacitor C8 is a feed back capacitor.,C9 and R13 connected to pin no 7 of IC 4 are tone corrector.R12 along with the VR1 variable resistor performs the sampling rate adjustment. R10 and R11 connected to pin26 and pin 27 of the microcontroller are voltage dropping resistors.
R15 and R16 connected to the base of transister Q1 and Q2 are voltage dropping resistors and drives transistors Q1 & Q2 when set to high logic by microcontroller. Q1 Drives the dial relay RL1and Q2 drives the off-hook relay.RL2.
R15 and R16 connected to the base of transister Q1 and Q2 are voltage dropping resistors and drives transistors Q1 & Q2 when set to high logic by microcontroller. Q1 Drives the dial relay RL1and Q2 drives the off-hook relay.RL2.
IC3 acts as buffer, R3 TO R8 are current limiting resistors and drives indication leds LD2 TO LD7 when PORT1 pins are set to low logic.
4×3 matrix keyboard is connected to PORT3 .keyboard is used to store the emergency telephone number .
PORT0 has open source internally so we have connected 4.7kX8 SIL,pullup resister to make them digital i/0 pins .This port is used as input port all the sensors are connected to this port.
4×3 matrix keyboard is connected to PORT3 .keyboard is used to store the emergency telephone number .
PORT0 has open source internally so we have connected 4.7kX8 SIL,pullup resister to make them digital i/0 pins .This port is used as input port all the sensors are connected to this port.
PGM SW is connected to P2.0 pin(21) of PORT2 is input pin this switch is used to store the telephone number. SW1 is alarm stop switch connected to pin22(P2.1)of the microcontroller,used as input pin. PORT2,pin number 24,25,26 and 27 are used as output pins.
All the input PORT pin logic state is normally high and they are active low.
All the output PORT pin logic state is normally low and thay are active high pin.
Port1 pins are normally high and they are active low;.
Circuit is driven by 9v 1 ampere transformer connected to PCON1
All the output PORT pin logic state is normally low and thay are active high pin.
Port1 pins are normally high and they are active low;.
Circuit is driven by 9v 1 ampere transformer connected to PCON1
Diode D1-D4 forms bridge circuit C1 ,C2 are filter capacitors,C3 is for noise filter.
Ic 7805 is 5v regulator ic to give stablised supply to microcontroller. Ld1 is a power indication led. Resister R1 is current limiting resistor
Ic 7805 is 5v regulator ic to give stablised supply to microcontroller. Ld1 is a power indication led. Resister R1 is current limiting resistor
1 comments:
This was a really wonderful post. Thank you for your provided information. office security systems
Post a Comment